Yard-man YM25 User Manual Page 17

  • Download
  • Add to my manuals
  • Print
  • Page
    / 68
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 16
17
Idle Speed Screw
Figure 33
SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS
Carburetor Adjustment
The idle speed of the engine is adjustable through the air
filter/muffler cover. See Figure 33.
NOTE: Careless adjustments can seriously damage your
unit. An authorized service dealer should make
carburetor adjustments.
Check Fuel Mixture
Old and/or improperly mixed fuel is usually the reason for
improper unit performance. Drain and refill the tank with
fresh, properly mixed fuel prior to making any
adjustments. Refer to Oil and Fuel Information.
Clean Air Filter
The condition of the air filter is important to the operation
of the unit. A dirty air filter will restrict air flow and change
the air/fuel mixture. This is often mistaken for an out of
adjustment carburetor. Check the condition of the air
filter before adjusting the idle speed screw. Refer to Air
Filter Maintenance.
Adjust Idle Speed
WARNING: The cutting attachment may
spin during idle speed adjustments. Wear
protective clothing and observe all safety
instructions to prevent serious personal
injury.
If, after checking the fuel mixture and cleaning the air
filter, the engine still will not idle, adjust the idle speed as
follows.
1. Start the engine and let it run at a high idle for a
minute to warm up. See Starting/Stopping
Instructions.
2. Release the throttle trigger and let the engine idle. If
the engine stops, insert a small Phillips or flat blade
screwdriver into the hole in the air filter/muffler cover.
See Figure 33. Turn the idle speed screw in,
clockwise, 1/8 of a turn at a time (as needed) until the
engine idles smoothly.
NOTE: The cutting attachment should not rotate when
the engine idles.
3. If the cutting attachment rotates when the engine idles,
turn the idle speed screw counterclockwise 1/8 of a
turn at a time (as needed), to reduce idle speed.
Checking the fuel mixture, cleaning the air filter, and
adjusting the idle speed should solve most engine
problems.
If this is not the case and the following are all true:
The engine will not idle
The engine hesitates or stalls on acceleration
There is a loss of engine power
Have the carburetor adjusted by an authorized service
dealer.
WARNING: After turning the unit off, make
sure the cutting attachment has stopped
before setting the unit down. This helps
prevent serious personal injury.
Page view 16
1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 67 68

Comments to this Manuals

No comments

Barco R9040411 Handbücher

Bedienungsanleitungen und Benutzerhandbücher für Projektoren Barco R9040411.
Wir stellen 1 PDF-Handbücher Barco R9040411 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung






Weitere Produkte und Handbücher für Projektoren Barco

Modelle Dokumententyp
R9001390 Bedienungsanleitung   Reality 9200 TCR+, 60 Seiten
R9827880 Bedienungshandbuch   Barco R9827880 Owner`s manual, 70 Seiten
CM50 Bedienungshandbuch   Barco CM50 Owner`s manual, 51 Seiten
HDF W series Bedienungsanleitung   HD Series drieluik.indd, 6 Seiten
RLM W8 Wartungshandbuch   Barco RLM W8 Service manual, 143 Seiten
R9001390 Bedienungsanleitung   PUB LFLT REALITY TCR+ E, 18 Seiten
R9001890 Bedienungshandbuch    Barco R9001890 Owner`s manual, 88 Seiten
ULTRA REALITY 7000 R9002810 Bedienungshandbuch   Barco ULTRA REALITY 7000 R9002810 Owner`s manual, 99 Seiten
CLM R10+ R9050100 Bedienerhandbuch   Barco CLM R10+ R9050100 Instruction manual, 199 Seiten
R9001569 Bedienungsanleitung    Reality 9300DLC, 59 Seiten
CINE7 R9010040 Bedienerhandbuch   Barco CINE7 R9010040 Instruction manual, 115 Seiten
CLM R10+ R90501005 Bedienerhandbuch   Barco CLM R10+ R90501005 Instruction manual, 229 Seiten
RLM W14 Betriebsanweisung   Barco RLM W14 User guide, 2 Seiten
R9040381 Bedienungshandbuch   Barco R9040381 Owner`s manual [en] , 247 Seiten
Galaxy NW-7 Bedienungsanleitung   Galaxy NW-EX series product specifications, 36 Seiten
R9001899 Bedienungsanleitung     SLM G5 - Barco, 86 Seiten
R9002038 Bedienungshandbuch   Barco R9002038 Owner`s manual, 57 Seiten
R9010310 Bedienungsanleitung   SLM R9+ Performer [v01], 135 Seiten
iD LR-6 R9010342 Bedienungsanleitung   iD LR-NR-6 brochure, 6 Seiten
R9000901 Bedienungsanleitung   Graphics 808S, 55 Seiten