Yard-Man YM20CS User Manual Page 7

  • Download
  • Add to my manuals
  • Print
  • Page
    / 52
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 6
7
STARTING INSTRUCTIONS
Fig. 9
Throttle Control
STOPPING INSTRUCTIONS
1. Release your finger from the throttle control. Allow the
engine to cool down by idling.
2. Press and hold On/Off Stop Control in the OFF (O) position
until engine comes to a complete stop (Fig. 9).
Fig. 11
1. Mix gas with oil. Fill fuel tank with fuel/oil mixture.
See Oil and Fuel Mixing Instructions.
NOTE: There is no need to turn the unit on. The
On/Off Stop Control is in the ON ( I ) position at all
times (Fig. 9).
2. Fully press and release the primer bulb 10 times,
slowly. Some amount of fuel should be visible in the
primer bulb and fuel lines (Fig. 10). If you can’t see
fuel in the bulb, press and release the bulb as many
times as it takes before you can see fuel in it.
3. Place the blue choke lever in Position 1 (Fig. 10).
4. Crouch in the starting position (Fig. 11), squeeze the
throttle control, and pull the starter rope out with a
controlled and steady motion 5 times.
NOTE: The unit uses Spring Assist Starting™, which
significantly reduces the effort required to start the
engine. You must pull the starter rope out far enough
to hear the engine attempt to start. There is no need
to pull the rope briskly-- there is no harsh resistance
when pulling. Be aware that this starting method is
vastly different from (and much easier than) what you
may be used to.
5. Place the blue choke lever in Position 2 (Fig. 10).
6. While squeezing the throttle control, pull the starter
rope out with a controlled and steady motion until
the engine starts.
7. Keep the throttle squeezed and allow the engine to
warm up for 15 to 30 seconds.
NOTE: Engine may take longer to warm up and reach
maximum operating speed at colder temperatures.
NOTE: Unit is properly warmed up when engine
accelerates without hesitation.
8. Once the engine is warmed up, place the blue choke
lever in Position 3 (Fig. 10). The unit is ready for use.
IF...
the engine hesitates, return the blue choke lever to
Position 2 (Fig. 10) and continue warm-up.
IF...
the engine does not start, go back to step 2.
IF...
the engine fails to start after a few attempts, place
the blue choke lever in Position 3 and squeeze the
throttle control. Pull the starter rope out with a
controlled and steady motion 3 to 8 times. The
engine should start. If not, repeat.
IF WARM...
If the engine is already warm, start the unit
with the blue choke lever in Position 2. After the unit
starts, move the blue choke lever to Position 3.
Start/On ( I )
Stop/Off (O)
Throttle
Control
Starting
Position
Trimmer
Equipped With
Spring Assist
Starting ™
Fig. 10
Blue Choke
Lever
Primer
Bulb
WARNING: Avoid accidental starting. Make sure
you are in the starting position when pulling the
starter rope (Fig. 11). To avoid serious injury, the
operator and unit must be in a stable position while
starting.
WARNING:
Operate this unit only in a well-
ventilated outdoor area. Carbon monoxide exhaust
fumes can be lethal in a confined area.
STARTING / STOPPING INSTRUCTIONS
Page view 6
1 2 3 4 5 6 7 8 9 10 11 12 ... 51 52

Comments to this Manuals

No comments

Barco R9040411 Handbücher

Bedienungsanleitungen und Benutzerhandbücher für Projektoren Barco R9040411.
Wir stellen 1 PDF-Handbücher Barco R9040411 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung






Weitere Produkte und Handbücher für Projektoren Barco

Modelle Dokumententyp
R9001390 Bedienungsanleitung   Reality 9200 TCR+, 60 Seiten
R9827880 Bedienungshandbuch   Barco R9827880 Owner`s manual, 70 Seiten
CM50 Bedienungshandbuch   Barco CM50 Owner`s manual, 51 Seiten
HDF W series Bedienungsanleitung   HD Series drieluik.indd, 6 Seiten
RLM W8 Wartungshandbuch   Barco RLM W8 Service manual, 143 Seiten
R9001390 Bedienungsanleitung   PUB LFLT REALITY TCR+ E, 18 Seiten
R9001890 Bedienungshandbuch    Barco R9001890 Owner`s manual, 88 Seiten
ULTRA REALITY 7000 R9002810 Bedienungshandbuch   Barco ULTRA REALITY 7000 R9002810 Owner`s manual, 99 Seiten
CLM R10+ R9050100 Bedienerhandbuch   Barco CLM R10+ R9050100 Instruction manual, 199 Seiten
R9001569 Bedienungsanleitung    Reality 9300DLC, 59 Seiten
CINE7 R9010040 Bedienerhandbuch   Barco CINE7 R9010040 Instruction manual, 115 Seiten
CLM R10+ R90501005 Bedienerhandbuch   Barco CLM R10+ R90501005 Instruction manual, 229 Seiten
RLM W14 Betriebsanweisung   Barco RLM W14 User guide, 2 Seiten
R9040381 Bedienungshandbuch   Barco R9040381 Owner`s manual [en] , 247 Seiten
Galaxy NW-7 Bedienungsanleitung   Galaxy NW-EX series product specifications, 36 Seiten
R9001899 Bedienungsanleitung     SLM G5 - Barco, 86 Seiten
R9002038 Bedienungshandbuch   Barco R9002038 Owner`s manual, 57 Seiten
R9010310 Bedienungsanleitung   SLM R9+ Performer [v01], 135 Seiten
iD LR-6 R9010342 Bedienungsanleitung   iD LR-NR-6 brochure, 6 Seiten
R9000901 Bedienungsanleitung   Graphics 808S, 55 Seiten